wholesale marilyn monroe jewelry Jewelry processing and production (2)

silver jewelry wholesaler china Design instructions:

The theme of this design is "Dream". I think of the collision between dreams and reality. The brooch and pendant are expressed in two patterns. Dreams are gorgeous like gems. No matter how blurred the dream, it lurks in our hearts, so that our mood will never get tranquility until the dream becomes reality. The production process uses carvings and sandblasting.

The step of the brooch:

1. Design pattern

In the design of the design pattern. Some changes.

2. Overclocking machine and sawing cutting

This to anneal red copper piece, and then pressed the compressor to the appropriate thickness. My red copper piece thickness is 1.2 mm. When passing the crusher machine, pay attention to putting it with your hand, do not pinch with a mule, first adjust the compressor to the original thickness of the red copper chip 2.0mm, and the thickness of the red copper decreases for the first time. 0.1mm. Cut off the paper film of the design pattern and cut it on the red copper chip. Use a knife to fell the edges smoothly.

3. 錾

This on the surface of the copper piece with a hammer to strike out the pattern. I forgot to take pictures of this step ...

4. Welding

This to polish the two copper pieces with sandpaper and smooth it, keep the surface clean and welded. Pay attention when welding After heating the object as a whole, concentrate the flames.

5. Make buckle

The buckle of the brooch consists of two parts. First, cut a suitable length of the copper strip of the rectangular body. To lift the knife, use a four -edged knife to frosted a small mouth on the copper bar. After the root bronze bars are expelled, it is bent with pliers. The other part is to cut the hollow copper tube a small section. Two twice clamp the objects to weld the two parts. When welding, pay attention to the overall heating and concentrate the flames, otherwise the buckle may be burned. After doing it, you can use a proper steel needle into a copper tube bend to form and complete the buckle.

6. Making inlaid

The copper sheet is cut according to the perimeter length of the habitat. Turn the copper sheet to bend the copper piece, use the glue hammer to form a ring, and then weld the connected gaps, and then make a small ring to support Hao Shi. Finally welded the mouth on the object.

7. Inlaid

In this step is to use fireball fixed objects, first heated the fireball to melt, put the objects above, wait until the object is fixed until the object is fixed, and then the hammer starts to start hammer. At the edge of the inlaid mouth, first hammer the direction of 12 o'clock, and then at 6 o'clock, 3 o'clock and 9 o'clock, the four points will fix the Hao Shi, then continue to hammer until Haoshi is completely fixed. Essence Then remove the objects and clean, and polish.

8. Sand spraying

The must ensure that the surface of the object is polished and clean before sandblasting, and there must be no frustration. Use the sandblasting machine to put on a mask. The tape is seal with the tape without sandblasting. I do the sandblast of the grid, and the rest is kept bright. Finally put it in the protective solution for 10 seconds and take it out. The brooch is done!

In steps of the pendant:

1. Design pattern and sawing

Come down, use a knife to fell flat.

2. Welding

The welded two parts of the saw.

3. Make melon seed buckle

This to cut the shape of the melon seed buckle from the copper tablet, the edges are fired and smooth, and fold it after the annealing. Use the copper wire to make a small circle, connect the small circle and the melon seed buckle, welded the melon seed buckle, and finally welded the small circle on the back of the object, so that the melon seed buckle can be moved.

4. Make claw setting

This to cut two copper wires and welded together, and then welded a small circle, folded them, fixed the position of the small circle, and fixed the position of the small circle. Can be fixed with soil and welded them. When welding, pay attention to the four points to be welded at the same time, and you cannot just burn in one point. After welding, cut off the excess part, put Hao Shi to test the stone, and welded the paws on the object.

5. Sand spray

This After cleaning and polishing, seal the part that does not need sandblasting with a tape and then sandblast. Finally put it in the protective solution for 10 seconds and take it out. The pendant is finished!